Wheelbuilding Totally Explained

Everything about Wheelbuilding totally explained

Wheelbuilding is the art and science of assembling a wheel (generally a bicycle wheel, although such wheels are also used on wheelchairs, motorcycles, and some cars, and known as wire wheels) from its component rim, spokes, nipples and hub.

Goals

A good wheelwright will ensure that the wheel is "true" in two ways: "lateral" (sideways wobble) and "radial" (roundness). Ideally spokes have similar tension (although the two sides will be different if a wheel is dished [dished:the uneven bracing angle of spokes on some multi speed wheels]) with tension high enough to give a rigid wheel and retain some tension under all loads but not so high as to lead to failure of spokes or the rim. Spokes should have no residual twist (windup) from tightening the nipples. The spokes may be "stress relieved", for example subjected to a greater tension during building than they're ever likely to encounter in use - usually by squeezing pairs of spokes together very hard. This is said to yield the spokes (and/or the hub) into a permanent shape where they bend around the hub flanges and each other.

Spoking

Spoking patterns may be or semi-tangential. For a normal wheel size and spoke count, only the latter is suitable for a wheel that has to transmit torque from the hub to the rim, as with rear wheels or hub brakes. This rule is occasionally broken where a very large number of spokes is used or the wheel is unusually small in diameter, either of which reduce the amount of bending stress on each radial spoke to an acceptable degree; some BMX bicycles and low-riders use radial spoking for both wheels. Rear wheels may also incorporate radial spoking on the non-drive side and semi-tangential spoking on the drive side. The most common spoking pattern is "three-cross" where each spoke crosses three others on the same flange of the hub before meeting the rim. The last cross is normally "interlaced" by wrapping the spoke around the one from the other side of the flange. Radial-spoked wheels, where the spokes don't cross each other, saves roughly the weight of two spokes (because the spokes are shorter) compared to a three-cross wheel but run the risk of tearing hub flanges apart, unless the hub is specifically designed for this pattern. Two-cross is sometimes used for hubs with large-diameter flanges (such as generator/dynamo hubs or large flange hubs), as it gives a more perpendicular spoke/rim angle, and four-cross is standard for spoke counts of 40 and above.

Bicycle wheels

Most conventional bicycle wheels now use 32 or 36 spokes front and rear, although the asymmetry of the rear wheel (to allow for the cluster of sprockets), and the additional weight it carries, means it benefits from having more spokes than the front. Commonly used models vary from 18 spokes for racing bikes to 36 for cross-country touring bikes to 48 spokes on tandems and heavily abused BMX bikes. The minimum number of spokes allowed for competition is 12. Some low-rider bicycles use as many as 144 brightly chromed spokes per wheel, although these are not meant for serious riding. Common rim diameters are 700c (sometimes 650c) for road/racing bikes, 27" or even 28" on older road bikes, 26" for most mountain bikes and 20" on BMXs and trials bikes. More recently a 24" wheel has found favour as a MTB/BMX cross for dirt jumping and street riding.
   Wheels can be built by machine instead of by hand. However, machine-built wheels are rarely as satisfactory as handbuilt wheels, partly because it's uneconomic to allow the machine to spend long enough on each wheel for a perfect result but also because most machines leave spokes with some residual twist. Machine-built wheels can be identified by their lacing pattern (if it isn't radial), as the spokes are laced the same on each side, rather than mirrored as on hand-built wheels. More modern "factory built" wheels such as Mavic's Ksyrium series are of quite different construction from that of a conventional wheel, trading a deeper and stronger rim for fewer spokes. They are popular, being aerodynamic and quite light (in the more expensive models) but not as durable, readily repairable or maintainable as a conventional wheel. Stainless steel is the most common material for spokes, although most mass-produced budget wheels use galvanised steel spokes. Other materials such as titanium, aluminium and some types of glass fibre and other composite materials are sometimes used. These materials are normally reserved for racing bikes and other specialist applications where weight, aerodynamics and performance are valued over durability and cost. DT Swiss and Sapim (Belgium) are two of the most popular spoke brands used in hand built wheels.
   Rims were traditionally made of steel but these days aluminium is by far most common and best choice due to its light weight, high durability and stiffness. Composite materials such as carbon fibre are sometimes used, but usually only for racing competitions such as time trial, triathlon and track cycling. Mavic (France), DT Swiss and Sun are popular makers of high quality bicycle rims.
   The canonical text on building conventional bicycle wheels is "The Bicycle Wheel" by Jobst Brandt, published by Avocet.

Motorcycle wheels

Motorcycle wheels or wire wheels typically use 36 or 40 spokes, of much heavier gauge than those on a bicycle. They are never "interlaced" in the manner described above, nor are "radial" builds recommended (except on wheels without brakes, which are not themselves a good idea). Adequate spoke tension is very important with motorcycle wheels, because of the greater torque applied to the wheel by an engine or disc brake. Loose spokes on a wheel fatigue rapidly and break, usually at the bend where they attach to the hub. When this happens, the wheel must be rebuilt using all new spokes, because even unbroken spokes in such a wheel are fatigued, and will usually break when tightened during the truing operation.

Spoke length

The correct length of spokes required can be calculated using rim diameter, hub flange diameter, hub width, lacing pattern, and number of spokes. See and. These calculations can be done either by hand (the old fashioned way - with a pen, paper and calculator) or by using a computer. There are many programs available and they range in complexity from simple Excel spreadsheets to stand alone desktop applications and web based calculators. An alternative method is to refer to a table which has the spoke lengths for a number of common hub and rim combinations.

Other conventions

A good wheelbuilder will ensure that the valve hole lies between two nearly parallel spokes to ease attachment of a pump head. This doesn't affect the structural integrity of the wheel, but it's unusual for this rule not to be observed.
It is also a convention, if the hub has a maker's label on its barrel, for the label to face (and be readable through) the valve hole. The rim labels should be readable from the right-hand side of the bicycle, as this is the side from which it's normally photographed. As the hub labels should face in the same direction front and rear (generally so they're readable from the seat), this means that even an undished, symmetrical front wheel has to be laced to the rim the "proper" way round, if perfection is the aim.

Further Information

Get more info on 'Wheelbuilding'.

External Link Exchanges

Do you know how hard it is to get a link from a large encyclopaedia? Well we're different and will prove it. To get a link from us just add the following HTML to your site on a relevant page:

<a href="http://wheelbuilding.totallyexplained.com">Wheelbuilding Totally Explained</a>

Then simply click through this link from your web page. Our crawlers will verify your link, extract the title of your web page and instantly add a link back to it. If you like you can remove the words Totally Explained and embed the link in article text.
As long as your link remains in place, we'll keep our link to you right here. Please play fair - our crawlers are watching. Your site must be closely related to this one's topic. Any kind of spamming, dubious practises or removing the link will result in your link from us being dropped and, potentially, your whole site being banned.